EV-ULTRA with 4 pair data

EV-ULTRA 3 CORE 4.0 SQMM SWA POWER + CAT5 CABLE

Manufactured in the UK This cable is designed for use in the installation of electric vehicle charge points. The cable incorporates power conductors and an enhanced Cat 5 screened data cable, encapsulated in a double sheathed design for extra protection. Whilst designed for use in electric vehicle charge points, the cable is also suitable for other installations where power and data is required. These cables are designed to be installed in air, clipped to surface, on cable tray/ladder work and embedded in concrete. The cables can be laid direct in the ground providing that suitable mechanical protection is in place.

SKU: EV-ULTRA3C4.0CAT5SWA

Reference: 10535493

Product Group: EV-ULTRA Cat5e

Supplier: Doncaster Cables

Contact Sales

Certifications & Standards

Quick Facts

SKU

EV-ULTRA3C4.0CAT5SWA

Reference

10535493

Product Group

EV-ULTRA Cat5e

Specifications

Technical Specifications

Weight

568.65

Unit

1000

Number of conductors

3 + DATA

Conductor Size

Construction

Plain Annealed Copper / Thermosetting XLPE / CarbonTek® /Galvanised steel wire armour / CarbonTek

Standard

BASEC CAD045 Approved

Conductor

Plain Annealed Copper Class 2 Stranded to BS EN 60228

Insulation

Thermosetting XLPE Type GP8 to BS 7655-1.3

Bedding

CarbonTek®

Armouring

Galvanised steel wire armour

Sheathing

CarbonTek®

Minimum Operating Temperature

-15°C

Maximum Operating Temperature

90°C

Minimum Bending Radius

8 x diameter

Reel Dimensions (mm)

1000x1000x600

Core Colours

Green/Yellow, Blue, and Brown

Nominal Stranding of Conductor (mm)

7/0.85

Nominal Radial Thickness of Insulation (mm)

0.7

Nominal Radial Thickness of Sheath (mm)

Nominal Overall Diameter of Bedding (mm)

12.5

Approximate Weight (kg/km)

510

Galv. Steel Wire Armour

0.9mm

Maximum Current Rating (A)

Voltage drop (mV/A/m)

Recommendations

Running data and power in a single cable is a concern for many electricians, with most believing that segregation of power (Band II) and data (Band I) is always required. It is however already common to find power and data inside one cable in many existing applications, an example is DALI networks which incorporate data within a 5 core power cable. It is recommended that the screening of the data cable is terminated to earth.

Voltage Band I

is defined as levels of voltage which are too low to provide serious electric shocks; effectively this limits the band to extra-low voltage (ELV), including telecommunications, signalling, bell, control and alarm circuits.

Voltage Band II

is defined as all voltages which are used in electrical installations not included in Band I. This means that all 230V supplies are included in Band II.

Proximity of Electrical services (extract from 528.1)

- Except where one of the following methods is adopted, neither a Band I nor a Band II circuit shall be contained in the same wiring system as a circuit of nominal voltage exceeding that of low voltage, and a Band I circuit shall not be contained in the same wiring system as a Band II circuit. (i) - Every cable or conductor is insulated for the highest voltage present. EV-Ultra® consists of power conductors and data cables that are rated to the same nominal voltage – therefore segregation of power and data is not required.

Proximity of communications cables

- Special considerations of electrical interference, both electromagnetic and electrostatic, may apply to telecommunication circuits, data transfer circuits and the like. EV-Ultra® has been designed with these considerations in mind, it incorporates screened, twisted pair data cables and is also constructed with a lay length that reduces interference. Laboratory and on-site installation tests have also been conducted and no interference or degredation of signal was recorded.

No specifications found matching ""